1. Manhole
2. Leak Detector
3. Manifold
4. Containment Sump
5. 4" Riser
6. Tank Adapter
7. Tank Manway
8. Column Pipe
9. Variable Length Coupler
10. Pump Motor Assembly (PMA)
11. End bell
12. Line Test Port, ¼" NPT
13. Leak Detector Port, 2" NPT
14. Syphon Port, ¼" NPT
15. Tank Port, ¼" NPT
16. Riser Pipe, 4" NPT
17. Discharge Outlet, 2" NPT
Notes: 1. Effective tank diameter (ETD) = Inside tank diameter (to top of 4" bung), including tank manway and/or sump adapter.
2. Model length (A) = ETD plus riser length minus bottom clearance minus 1" thread engagement.
3. Riser length (B) = Bury depth (to top of tank) minus pump head clearance minus tank manway and/or minus sump adapter.
Biofuel Blend CompatibilityFE PETRO® pumps are UL listed with both UL79A (up to 85% Ethanol) and UL79B (up to 20% or 100% Biodiesel).
Advanced ProtectionStop corrosion in its tracks. Special powder-coated, e-coated, and stainless steel components defend your pump in the tank and in the sump from accelerated corrosion.
Turbine Pump InterfaceRemote enhanced pump monitoring and control including pump-in-water automation, clogged intake escalation, tank leveling, and tank priority.
Intake Filter ScreenAvoid system damage, pumping slowdowns, and reduce filter changes by keeping harmful tank debris, sediment, and corrosion from entering the pumping system with this factory-installed option.
Variable SpeedWith faster fill times during peak hours and power savings during non-peak hours, variable speed submersible pumping systems allow you to maximize profits with consistent flow rates while mitigating operating expenses.
MagShell®The patented stainless steel MagShell® is designed to maximize flow rate capabilities, potential throughput, and profits. By expanding the pump motor shell, the MagShell® increases the area for product flow by 45%.
Variable LengthThe patented telescoping pump shaft lets installers adjust the length of the pump onsite for the perfect fit.
Active Air EliminatorFE PETRO® STPs come standard with active air elimination, which eliminates air through the highest point in the pump head at all times when the pump is running, assuring air does not pass into discharge piping.
Safety and Ease of MaintenanceFE PETRO® STPs include a contractor electrical disconnect, which requires loosening only one bolt, allowing motor wiring to be disconnected without venting the dangerous tank vapors into the sump when servicing FE PETRO® submersible products.
Simple ServicingIf ever required, the pump can be easily removed from the tank by unthreading three bolts. There is no need to disconnect the syphon system or to remove the leak detector from the system to service the STP.
Manual Pressure ReliefAs a standard FE PETRO® feature, a vent screw is provided to bleed line pressure to zero when necessary. By turning this screw, product is diverted back to the tank, dropping line pressure to zero. This reduces fuel discharged into the sump manhole or dispenser pan during servicing, further protecting service technicians and the environment.
Outlast, Outperform with Franklin Electric InsideFE PETRO® STPs are powered by the legendary Franklin Electric motor and built for long term performance. Franklin Electric-powered submersible pumps provide maximum uptime and a proven track record in the fueling industry that spans more than four decades. They feature best-in-class flow rates and a long history of dependability.
Quality CertificationFranklin Fueling Systems is an ISO 9001 Certified Manufacturer.
Variable speed models are available in variable lengths only.
Check valve: 2¾" (70mm) diameter fluorocarbon seal constructed with cast aluminum body and steel backing washer.
Pressure relief valve: available in four pressure relief settings, integral to check valve. Standard model relieves at 40 psi (2.8 bar) and resets above 35 psi (2.4 bar).
Syphon: venturi-type syphon primer supplied with every submersible. Syphon check valve and secondary syphon sold separately.
Air eliminator: every submersible includes a tank return path with one-way check valve to provide active air elimination.
Electrical disconnect: electrical yoke for positive contractor disconnect during service.
4 Hp, variable speed, two-stage centrifugal type pump motor with integral, automatic, thermal overload protection.
60 Hz Max. pressure: selectable operating pressure on MagVFC™ between 24 psi and 42 psi deadhead.
50 Hz Max. pressure: selectable operating pressure on EcoVFC™ between 1.65 bar and 2.90 bar deadhead.
Available with MagShell® which results in 45% increased flow area around motor.
Variable speed pumps can only be controlled by a MagVFC™ variable frequency controller.
VS4 models require three-phase incoming power supply to the MagVFC™ for proper operation.
Incoming power supply to the MagVFC™ can be 200-250 VAC, 50 or 60 Hz.
MagVFC™ outputs a three-phase, variable frequency signal, valid for FE PETRO® variable speed pumps only.
MagVFC™ max. line draw: 20 Amps.
Max motor draw: 15 Amps.
Max. liquid viscosity: 70 SSU at 60 °F (15 °C).
STP variable speed models are UL listed for fuel mixtures containing up to 10% ethanol, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.
IST/ISTAP variable speed models are UL and cUL listed for fuel mixtures containing diesel fuel with up to 20% Biodiesel, 100% Biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.
All variable speed models can also be used with diesel fuels, fuel oils, kerosene, Avgas and jet fuels in a non-gelled pourable state.
All wetted elastomers are made of a high grade, fluorocarbon compound.
STP Standard Submersible Turbine Pumps with Fixed or Variable Speed Pump Motor Assembly
UL79 for petroleum dispensing products intended for use with gasoline or gasoline/ethanol blends with nominal ethanol concentrations up to 10 percent (gasohol, E10), diesel fuel, diesel/biodiesel blends with nominal biodiesel concentrations up to 5 percent (B5), kerosene, or fuel oil.
20% MTBE, 20% ETBE or 17% TAME with gasoline.
STPAG, STPAP, IST, ISTAP Alcohol-Grade Compatible and Advanced Protection Fixed or Variable Speed Submersible Turbine Pumps
UL79A for gasoline and gasoline/ethanol blends with nominal ethanol concentrations up to 85 percent (E0 - E85) for products intended for use with gasoline or gasoline/ethanol blends with nominal ethanol concentrations up to 85 percent (E85).
20% MTBE, 20% ETBE or 17% TAME with gasoline.
UL79B for diesel fuel, biodiesel fuel, diesel/biodiesel blends with nominal biodiesel concentrations up to 20 percent (B20), kerosene, and fuel oil for products intended for use with diesel fuel, biodiesel fuel, diesel/biodiesel blends with nominal biodiesel concentrations up to 20 percent (B20), kerosene or fuel oil.
100% biodiesel.
cULus listed.
Consult factory for applicable approvals.
For 50 Hz performance charts, please see the 50Hz-Submersible Turbine Pumps-Datasheet in Downloads.
4 Hp Variable Speed Submersible Turbine Pumps
| Model | Description | Model Length Range Number | Model Length Range* |
|---|
| STPMVS4-VL1 | 4 Hp variable speed with MagShell® | VL1 | 64" – 92" |
| STPMVS4-VL2 | 4 Hp variable speed with MagShell® | VL2 | 95" – 156" |
| STPMVS4-VL3 | 4 Hp variable speed with MagShell® | VL3 | 127" – 218" |
4 Hp Variable Speed Intelligent Submersible Turbine Pumps
| Model | Description | Model Length Range Number | Model Length Range* |
|---|
| ISTMVS4-VL1 | 4 Hp variable speed with MagShell® | VL1 | 64" – 92" |
| ISTMVS4-VL2 | 4 Hp variable speed with MagShell® | VL2 | 95" – 156" |
| ISTMVS4-VL3 | 4 Hp variable speed with MagShell® | VL3 | 127" – 218" |
| ISTAPMVS4-VL1 | 4 Hp AG variable speed with Advanced Protection, and MagShell® | VL1 | 64" – 92" |
| ISTAPMVS4-VL2 | 4 Hp AG variable speed with Advanced Protection, and MagShell® | VL2 | 95" – 156" |
| ISTAPMVS4-VL3 | 4 Hp AG variable speed with Advanced Protection, and MagShell® | VL3 | 127" – 218" |
Factory Installed Options
| Model | Description |
|---|
| F | Floating suction adapter, 1½" NPT female, must be factory installed |
| K | IFS (intake filter screen) factory assembled to pump motor assembly |
| R | Model R check valve, factory installed, for Veeder-Root® PLLD Line Leak |
Intelligent submersible turbine pump specific accessories - 60Hz
| Model Number | Description |
|---|
| 5874202800 | MagVFC™, 2 Hp or 4 Hp Variable Frequency Controller, 220 V, one required per STP |
| 400137908 | Syphon check valve, alcohol-gasoline compatible (when ordered with STP/IST) |
| 5800300100 | STP-DHI, dispenser hook isolation for 110 Volt dispenser handle switches, up to eight each |
| 402459931 | Model 65 psi check valve (for secondary manifolded STPs with Veeder-Root® PLLD), AG compatible |
| 402507930 | Secondary syphon kit (when two syphon primes are required for one STP) |
Intelligent submersible turbine pump specific accessories - 50Hz
| Model Number | Description |
|---|
| 5874202900 | EcoVFC™, 2 Hp or 4 Hp Variable Frequency Controller, 380 V, one required per STP |
| 400137937 | Syphon check valve, alcohol-gasoline compatible |
| 402459931 | Model 65 psi check valve (for secondary manifolded STPs with Veeder-Root® PLLD), AG compatible |
| 402507930 | Secondary syphon kit (when two syphon primes are required for one STP) |
| 5800300200 | STP-DHIB, dispenser hook isolation for 240 Volt dispenser handle switches, up to eight each |